Before Launching BatchPro
1. Open Notepad.
2. Copy and paste the below information.
| KCS East St Louis IL Chicago IL CPRS Montreal PQ Detroit MI CN Vancouver BC Toronto ON |
3. Choose File > Save As. Set the filename as "Example.in"
Note: All "input" files must end with the .in extension. You will need to change the Type to All Files. |
4. Create a .cfg file that represents the data inside Example.in. Please use Notepad for this as well. An example is below:
| [Batch File Options] "CarIDEnd"=0 "CarIDStart"=0 "CarNumberEnd"=0 "CarNumberStart"=0 "DestinationEnd"=51 "DestinationRREnd"=5 "DestinationRRStart"=1 "DestinationStart"=29 "LoadedIndex"=0 "OriginEnd"=28 "OriginRREnd"=5 "OriginRRStart"=1 "OriginStart"=6 [Batch Processor Options] "BatchChunkSize"=1 "LineFormat"=1 "UseDelimiter"=0 [Batch Report Options] "CarrierCarrierIDReport"=0 "CarrierIDReport"=0 "CarrierReport"=0 "CarrierStateReport"=0 "DetailedReport"=0 "RoundMiles"=0 "StateCarrierIDReport"=0 "StateReport"=0 [Batch Route Options] "DestinationGeocodeType"=3 "OriginGeocodeType"=3 "OutputType"=0 "RouteFormula"=0 "TerminalSwitching"=2 |
5. Choose File > Save As. Set the filename as "Example.cfg". Remember to change the Type to All Files.
6. Launch Rail-BatchPro. At first it will look like this:
7. Under Input File. choose Browse. Navigate to your Example.in file. Do the same for Configuration File. Your user interface should now look like this:
| Note: If you forgot to choose Report options in the .cfg file, it is not too late. You may check what you need under "Optional". For this example, we will be checking "Detailed Report (.RPT File)". |
8. Choose Run. Head to the Output Report File location. It will be in the same folder as your .in file. Open it using Notepad. The .out file should look like this:
| KCS East St Louis IL Chicago IL 810.3 CPRS Montreal PQ Detroit MI 572.3 CN Vancouver BC Toronto ON 2754.3 |
9. Since Detailed Report was checked, a .RPT file was created in the same area as well. Open it using notepad. A small sample of the .RPT file should look like this:
| Report for Line# 1 in OUT file: DETAILED REPORT East St Louis, IL (KCS) to Chicago, IL (KCS) 810.3 Miles, Practical, Include Intermodal-Only RRSTStation NameLeg MilesTotal Miles Origin: East St Louis, IL KCSILQ Tower 0.3 0.3 KCSILK Tower 0.2 0.5 KCSILVenice Jct 0.8 1.3 KCSILVenice 0.8 2.1 KCSILWr Tower 3.5 5.6 KCSILGranite City 0.1 5.7 KCSILNameoki 2.7 8.4 KCSILMitchell 3.2 11.6 KCSILLenox 0.1 11.7 KCSILHartford 4.4 16.1 KCSILWood River 2.1 18.2 KCSILWann 0.9 19.1 KCSILEast Alton 0.5 19.6 KCSILUpper Alton 2.9 22.5 KCSILGodfrey 4.0 26.5 KCSILDelhi 7.8 34.3 KCSILJerseyville 6.6 40.9 Note: The .RPT will output a large amount of data. Above is only a small sample of the .RPT file. |
